[Mangorille] WTFOS & COMPATIBILITY Issue Fix | DJI Goggles V2 Gets Native Betaflight 4.4 HD OSD

🎯 Загружено автоматически через бота: 🚫 Оригинал видео: 📺 Данное видео является собственностью канала Mangorille. Оно представлено в нашем сообществе исключительно в информационных, научных, образовательных или культурных целях. Наше сообщество не утверждает никаких прав на данное видео. Пожалуйста, поддержите автора, посетив его оригинальный канал: @Mangorille. ✉️ Если у вас есть претензии к авторским правам на данное видео, пожалуйста, свяжитесь с нами по почте support@, и мы немедленно удалим его. 📃 Оригинальное описание: The DJI Goggles V2 also supports the Betaflight 4.4 native HD OSD when paired with the O3 air unit. However, if you have WTFOS installed, there is a compatibility issue that causes the Canvas Mode menu option to disappear from the Display menu on the goggles. These instructions will resolve that. Thanks to K1200S08 for sharing these instructions with me! ========================= Items suggested in this video ========================= My Favorite Screwdrivers (Wiha Slotted & Phillips): Amazon US: Amazon Canada: DJI Goggles 2 Integra: Amazon US: Amazon Canada: GetFPV: DJI FPV Goggle V2: Amazon US: Amazon Canada: DJI O3 Air Unit: Amazon US: Amazon Canada: GetFPV: DJI FPV Remote Controller 2: Amazon US: Amazon Canada: XING2 1404 4600kv Motors: Banggood: GetFPV: iFlight 20x20mm F7 Flight Stack: Banggood: GetFPV: HQ T3x3x3 Props Banggood: GetFPV: TBS Crossfire Nano Receiver with Immortal T Antenna GetFPV: TBS Tango 2 Pro GetFPV: SpeedyBee F7 Mini 35A 3-6S 8-bit Flight Controller Stack: GetFPV: XING2 1404 4600kv Motors: Banggood: GetFPV: Happymodel EP1 ELRS Receiver: AliExpress: GetFPV: HQ T3x3x3 Props Banggood: GetFPV: ========================= Instructions & CLI Commands ========================= Here are the steps you should follow to get both O3 OSD HD and WTFOS work (MUST do in the exact order): - Boot the goggles into FPV System (DIY) mode and connect to FPVWTF configurator - Remove WTFOS and reboot into O3 mode - Connect to DJI Assistant (Consumer Drone series) and update firmware to - After update completed, swith back to FPV System (DIY) mode, reboot and connect to configurator - Run the CLI commands: unrd 0 unrd 0 unrd 1 reboot - After the goggles rebooted, the configurator detected the slot problem and offered an automatic fix. Accept the fix. - After automated fix applied, re-install WTFOS - Reinstall packages (msp-osd, etc) ============================ Videos you may want to check out ============================ How to get your custom BetaFlight OSD working on the DJI O3 Air Unit | MSP Canvas Mode is HERE! You FINALLY Did It! | DJI Goggles 2 Native Betaflight 4.4 HD OSD Now Officially Supported FULLY Customizable HD OSD canvas mode for DJI FPV Goggles V1 & V2 | My EYES can’t handle the BEAUTY! Playlist: DJI O3 Digital FPV System | Reviews, Guides, & How Tos #djifpv #fpv #drones Mandatory Disclaimer: I participant in the Amazon Services LLC Associates Program, which is an affiliate advertising program designed to provide a means to earn fees by linking to and affiliated sites. Item suggestion links above are affiliate links and I will receive compensation if you choose to use them. There is no cost to you to use these links and any compensation received goes right back into the channel.