0:40 Description 1:08 Inside 2:15 Small Coin 2:52 Other perspective 3:55 Big Metal 4:22 Needle 4:58 Near Metal 5:35 Differeent objects 6:31 Schematic diagram 7:53 Building
A traditional metal detector can locate a burried item and give you a rough location of the object belw the ground
A pinpointer enables you to pin down an object’s location , make a smaller hole when digging , and extract the item. Also, it can be used as Handheld metal detector used by emergency responders to conduct security screening of individuals at access control checkpoints.
The device described above is very simple and contains a detector part consisting of a transistor, a ferrite core with windings and several more passive elements, and an Arduino Nano microcontroller with signaling elements and a calibration switch.
The method of working with the metal detector is as follows. The device switches on and after a few seconds the calibration switch is pressed. The device is now ready to detect metal we bring the probe closer to a metal object, the LED starts flashing and the Buzzer emits an intermittent sound. The closer we get to the subject, the higher the flashing frequency . The sensitivity of the detector is surprisingly good, considering that it is a very simple device and does not require any settings. Detects a small metal coin at a distance of 4-5 cm, and larger metal objects at a distance of 10 cm and more. In fact, its purpose is to locate more accurately the object that was previously detected with a standard metal Arduino code is taken from the site and is made in FLPROG visual programming tool.
There is also an LED on the front that serves to illuminate the environment if we are looking for objects in dark diode is activated by holding the calibration switch for 5 seconds, and the same applies to deactivation.
The device is powered by two lithium ion batteries connected in series and the consumption is extremely low, about 20mA in standby mode and 40-45mA when detecting a metal object so the battery lasts very , the whole assembly is built into a suitable box made of PVC material.
Instructions , schematic and code at:
If you are interested in this area, see the Playlist with all my Metal Detectors at:
Visit my Youtube Channel for more Projects , DIY and How To Make videos:
by mircemk
SUBSCRIBE LIKE AND SHARE !!!!
Thanks for your Support !
Song: Jarico - Landscape (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link:
#NoCopyrightMusic #VlogMusic #VlogNoCopyrightMusic
1 view
203
64
1 month ago 00:21:59 1
Open Sim Shifter H Assembly - DIY 3D Print - Arduino - Sim Racing
1 month ago 00:03:49 1
Обзор на перистальтический насос Kamoer KPHM100. Сделай гидропонику на Arduino своими руками.
1 month ago 00:34:22 1
Robot Sylvie tête partie 5: Robot humanoïde imprimé en 3D ! #diy #robot #3dprinting
1 month ago 00:06:36 1
Make an Arduino Temperature Sensor (Thermistor Tutorial)
1 month ago 00:09:30 1
3D printed Vibration Rock Tumbler with magnetic drive
1 month ago 00:00:47 1
🛠 Про ремонт китайских и российских 3D-принтеров
1 month ago 01:24:14 8
В гостях у RangeVision! Поговорим о 3D-сканировании! Как работают современные 3D-сканеры?
1 month ago 00:18:29 1
✅Сделай сам сторожа Летающую собаку для квартиры, гаража, дачи. Самодельная охранная сигнализация.
1 month ago 00:17:08 1
Печать напрямую ПЭТ лентой из пластиковой бутылки. DIY: Лента из ПЭТ и 3D печать.
1 month ago 00:09:06 1
Крутой аккумулятор 9Ач для электроинструментов своими руками
1 month ago 01:21:14 1
Как обработать модели из PLA, PETG, ABS, SBS и тд при помощи растворителей? Химическая постобработка
1 month ago 00:02:15 1
Unboxing Bldc cooler Kit | small mistake big issue | client reviews: Alam Ansari #bldcmotor
1 month ago 00:13:59 1
ХОЛОДНЫЙ КАМИН ИЗ БОЧКИ И ЭПОКСИДКИ
1 month ago 00:17:40 1
How to Make a Simple Egg Incubator at home || Pets Life TV
2 months ago 00:31:57 1
Точечная сварка под микроскопом
2 months ago 00:10:43 8
Звуковая - акустическая левитация, собираем за 20 минут своими руками
2 months ago 00:22:03 1
Лазерный гравер своими руками из DvD приводов laser engraver
2 months ago 00:02:43 1
Самодельный манипулятор на Arduino, Raspberry с ROS2 для обучения школьников. Механика - Часть 1!
2 months ago 00:00:50 1
Какими материалами приходится печатать на домашней ферме 3D-принтеров?
2 months ago 00:07:27 1
ШИМ регулятор напряжения на NE555 своими руками
2 months ago 00:00:16 1
Такого вы ещё не видели!! #diy #wireing #welding #энерголикбез
2 months ago 00:00:37 1
⚙️ Как настроить Prusa Slicer под свой 3D-принтер?
2 months ago 00:15:17 1
I built a mouse from scratch with 3D printing and Arduino